Electrochemical methods, weight loss and surface analysis technique were used to study the effect of glutamic acid on the corrosion of Fe-19Cr stainless steel in 1 M hydrochloric acid solution. Results revealed that the corrosion inhibition of glutamic acid of Fe-19Cr in 1 M HCl was enhanced in the presence of the iodide ions due to synergistic effect. In the absence of KI, the inhibition of Fe-19Cr corrosion by glutamic acid was glutamic acid concentration dependent. Potentiodynamic polarization curves demonstrated that glutamic acid acts as a mixed type inhibitor. Self-Assembled Monolayers of glutamic acid were able to protect stainless steel from corrosion effectively. The adsorption of the inhibitor onto the stainless steel surface follows Langmuir adsorption isotherm. The value of free energy of the adsorption indicated that there is a physical interaction between the glutamic acid and the stainless steel surface.

During turning operations, tool-part-chip contact causes wear to the cutting tool. The objective of this work is to study the wear of the clearance faces of tungsten carbide cutting tools during turning operations. Experimental tests on tool life for dry turning operations were carried out at four different cutting speeds, where the feed rate and the depth of cut are kept at constant values: 0.08 mm/rev for feed rate and 0.5 mm for depth of cut. An analysis of the influence of cutting parameters on the tools wear and consequently tool life (Τ) was presented, then the roughness of the machined surface Ra and the morphology of the chips produced were studied. This study makes it possible to identify that the wear mechanisms and the tool life are strongly linked to the roughness of the machined surfaces and to the morphology of the chips produced during the turning operations.

Today, and to quickly meet the high demands of variability, supply chain efficiency and energy optimization, business markets are looking for modern manufacturing technologies and as a solution, industry 4.0 is using the benefits of integrating modern manufacturing technologies and information systems to promote production capabilities. In this context, intelligent industry represents a new generation of automatic production systems based on the concepts of intelligent industry, intelligent manufacturing, control and intelligent inspection, such as inspection on coordinate measuring machines (CMMs). This technology allows many machines to be integrated into a plant and controlled online using the MBD (Model Based Design) quality system. The problem of conformity of parts with complex geometry is becoming more and more important. The objective of this work is to present a 3D inspection technique on a virtual model (MBD: Model Based Design), using a coordinate measuring machine equipped with a “POWER INSPECT” measurement and inspection software. The interest of this technique is to show the impact of the dimensional inspection and geometric tolerance process of the CAD model for the CAI (Computer aided Inspection) approach on the fidelity of the finished product for additive manufacturing (AM) including intelligent industry.

The coflex Interlaminar Technology is an interlaminar stabilization device indicated for use in one or two level lumbar stenosis from L1-L5. It is used in skeletally mature patients with at least moderate impairment in function who experience relief in flexion from their symptoms of leg/buttocks/groin pain, with or without back pain, and who have undergone at least 6 months of non-operative treatment. Our study is focused on the evaluation and biomechanical analysis of osteosynthesis implants and in particular the Corflex-F implant to redefine a new approach to the "Coflex" interspinatus implant using particles swarm optimisation for additive manufacturing, then to study these biomechanical performances.

Today, and to quickly meet the high demands of variability, supply chain efficiency and energy optimization, business markets are looking for modern manufacturing technologies and as a solution, industry 4.0 is using the benefits of integrating modern manufacturing technologies and information systems to promote production capabilities. In this context, intelligent industry represents a new generation of automatic production systems based on the concepts of intelligent industry, intelligent manufacturing, control and intelligent inspection, such as inspection on coordinate measuring machines (CMMs). This technology allows many machines to be integrated into a plant and controlled online using the MBD (Model Based Design) quality system. The problem of conformity of parts with complex geometry is becoming more and more important. The objective of this work is to present a 3D inspection technique on a virtual model (MBD: Model Based Design), using a coordinate measuring machine equipped with a “POWER INSPECT” measurement and inspection software. The interest of this technique is to show the impact of the dimensional inspection and geometric tolerance process of the CAD model for the CAI (Computer aided Inspection) approach on the fidelity of the finished product for additive manufacturing (AM) including intelligent industry.

Electrochemical methods, weight loss and surface analysis technique were used to study the effect of glutamic acid on the corrosion of Fe-19Cr stainless steel in 1 M hydrochloric acid solution. Results revealed that the corrosion inhibition of glutamic acid of Fe-19Cr in 1 M HCl was enhanced in the presence of the iodide ions due to synergistic effect. In the absence of KI, the inhibition of Fe-19Cr corrosion by glutamic acid was glutamic acid concentration dependent. Potentiodynamic polarization curves demonstrated that glutamic acid acts as a mixed type inhibitor. Self-Assembled Monolayers of glutamic acid were able to protect stainless steel from corrosion effectively. The adsorption of the inhibitor onto the stainless steel surface follows Langmuir adsorption isotherm. The value of free energy of the adsorption indicated that there is a physical interaction between the glutamic acid and the stainless steel surface.

The coflex Interlaminar Technology is an interlaminar stabilization device indicated for use in one or two level lumbar stenosis from L1-L5. It is used in skeletally mature patients with at least moderate impairment in function who experience relief in flexion from their symptoms of leg/buttocks/groin pain, with or without back pain, and who have undergone at least 6 months of non-operative treatment. Our study is focused on the evaluation and biomechanical analysis of osteosynthesis implants and in particular the Corflex-F implant to redefine a new approach to the "Coflex" interspinatus implant using particles swarm optimisation for additive manufacturing, then to study these biomechanical performances.

During turning operations, tool-part-chip contact causes wear to the cutting tool. The objective of this work is to study the wear of the clearance faces of tungsten carbide cutting tools during turning operations. Experimental tests on tool life for dry turning operations were carried out at four different cutting speeds, where the feed rate and the depth of cut are kept at constant values: 0.08 mm/rev for feed rate and 0.5 mm for depth of cut. An analysis of the influence of cutting parameters on the tools wear and consequently tool life (Τ) was presented, then the roughness of the machined surface Ra and the morphology of the chips produced were studied. This study makes it possible to identify that the wear mechanisms and the tool life are strongly linked to the roughness of the machined surfaces and to the morphology of the chips produced during the turning operations.